YANG models

The data models describe much more than the switch implements. The switch accepts only the settings below and rejects everything else when you commit, with an error such as config/mtu is not supported. Settings it does not implement are accepted only with their default value, because the data model fills them in everywhere (for example auto-negotiate true or loopback-mode NONE).

Paths are written as in the CLI. {…} lists the supported leaves.

Interfaces (openconfig-interfaces, openconfig-if-ethernet, openconfig-vlan, openconfig-if-ip)

Path	Notes
interfaces interface <name> config {name, type, enabled, description}	type is ianaift:ethernetCsmacd for switch ports or ianaift:l3ipvlan for routed VLAN interfaces.
interfaces interface <port> ethernet switched-vlan config {interface-mode, access-vlan, native-vlan, trunk-vlans}	interface-mode is ACCESS or TRUNK. 802.1Q mode only.
interfaces interface <name> routed-vlan config vlan	VLAN id or name, or port-based group id or name.
interfaces interface <name> routed-vlan ipv4 addresses address <ip> config {ip, prefix-length}	Static IPv4 addresses.
interfaces interface <name> routed-vlan ipv4 config dhcp-client	At most one interface.

VLANs (clixon-switch)

Path	Notes
vlans vlan <id> config {vlan-id, name, status}	status is ACTIVE (default) or SUSPENDED. 802.1Q mode only.
switch config vlan-mode	DOT1Q (default) or PORT_BASED.
port-based-vlans group <id> config {id, name, port}	Port-based mode only.

Spanning tree (openconfig-spanning-tree)

Path	Notes
stp global config {enabled-protocol, bpdu-guard, bpdu-filter}	enabled-protocol: one of oc-stp-types:RSTP, oc-stp-types:MSTP, sw:STP.
stp rstp config {hello-time, max-age, forwarding-delay, hold-count, bridge-priority}	Also used for STP.
stp rstp interfaces interface <port> config {name, cost, port-priority}
stp mstp config {name, revision, max-hop, hello-time, max-age, forwarding-delay, hold-count, bridge-priority}	bridge-priority is the CIST's.
stp mstp interfaces interface <port> config {name, cost, port-priority}	CIST ports.
stp mstp mst-instances mst-instance <id> config {mst-id, vlan, bridge-priority}
stp mstp mst-instances mst-instance <id> interfaces interface <port> config {name, cost, port-priority}
stp interfaces interface <port> config {name, edge-port, link-type, guard, bpdu-guard, bpdu-filter}	guard is ROOT or NONE.

LLDP (openconfig-lldp)

Path	Notes
lldp config {enabled, hello-timer}	hello-timer: 1 … 3600 seconds, default 30.
lldp config {system-name, system-description}	One line each. Default: the host name, and the firmware name and version.
lldp config suppress-tlv-advertisement	oc-lldp-types:MANAGEMENT_ADDRESS, oc-lldp-types:SYSTEM_CAPABILITIES.
lldp interfaces interface <port> config {name, enabled}	Switch ports only.

SNMP (ietf-snmp)

Path	Notes
snmp engine {enabled, engine-id}
snmp engine version v3	Required; the only version.
snmp engine listen <name> udp {ip, port}	IPv4 addresses.
snmp usm local user <name> auth sha key	Required for every user. 20 octets.
snmp usm local user <name> priv aes key	Optional. 16 octets.
snmp vacm group <name> member <user> security-model usm
snmp vacm group <name> access "" <model> <level> read-view <view>	<model> is usm or any, <level> is auth-no-priv or auth-priv.
snmp vacm view <name> {include, exclude}	Numeric OIDs, no wildcards.

System (clixon-switch)

Path	Notes
system config {contact, location}	One line each, up to 255 characters.

Status only

These show up in show state but cannot be configured:

• system state: host name, firmware version and the revision it was built from, uptime, load, memory, clock
• port counters, oper-status, MAC address
• routed-vlan ipv4 state dhcp-lease and each address's origin
• stp ... state: roles, port states, root bridge
• lldp state and lldp interfaces interface <port> state: what the switch announces, counters
• lldp interfaces interface <port> neighbors: the neighbors of each port
• snmp engine engine-id-in-use
• the MIBs served over SNMP (BRIDGE-MIB, Q-BRIDGE-MIB, RSTP-MIB, LLDP-MIB)